Chinese Journal of Mechanical Engineering is affiliated with the Chinese Mechanical Engineering Society.
Articles
Page 5 of 18
-
Citation: Chinese Journal of Mechanical Engineering 2023 36:14
-
Ultralong Stretchable Soft Actuator (US2A): Design, Modeling and Application
Actuator plays a significant role in soft robotics. This paper proposed an ultralong stretchable soft actuator (US2A) with a variable and sizeable maximum elongation. The US2A is composed of a silicone rubber tub...
Citation: Chinese Journal of Mechanical Engineering 2023 36:13 -
Application of Nonlinear Lamb Wave Mixing Method for Residual Stress Measurement in Metal Plate
Harmonic nonlinear ultrasound can offer high sensitivity for residual stress measurements; however, it cannot be used for local stress measurements at a point in space and exhibits nonlinear distortions in the...
Citation: Chinese Journal of Mechanical Engineering 2023 36:12 -
Tribological Performance of Different Concentrations of Al2O3 Nanofluids on Minimum Quantity Lubrication Milling
Nanofluid minimum quantity lubrication (NMQL) is a green processing technology. Cottonseed oil is suitable as base oil because of excellent lubrication performance, low freezing temperature, and high yield. Al2O3
Citation: Chinese Journal of Mechanical Engineering 2023 36:11 -
Progressive Failure Analysis of Composite/Aluminum Riveted Joints Subjected to Pull-Through Loading
Out-of-plane mechanical properties of the riveted joints restrict the performance of the wing box assembly of airplane. It is necessary to investigate the pull-through performance of the composite/metal rivete...
Citation: Chinese Journal of Mechanical Engineering 2023 36:10 -
Denoising Fault-Aware Wavelet Network: A Signal Processing Informed Neural Network for Fault Diagnosis
Deep learning (DL) is progressively popular as a viable alternative to traditional signal processing (SP) based methods for fault diagnosis. However, the lack of explainability makes DL-based fault diagnosis m...
Citation: Chinese Journal of Mechanical Engineering 2023 36:9 -
A Compensation Algorithm for Large Element Characterizing the Damage Evolution Process and Its Application to Structure Collisions
When simulating the process from elastic–plastic deformation, damage to failure in a metal structure collision, it is necessary to use the large shell element due to the calculation efficiency, but this would ...
Citation: Chinese Journal of Mechanical Engineering 2023 36:8 -
Online Identification of Lithium-ion Battery Model Parameters with Initial Value Uncertainty and Measurement Noise
Online parameter identification is essential for the accuracy of the battery equivalent circuit model (ECM). The traditional recursive least squares (RLS) method is easily biased with the noise disturbances fr...
Citation: Chinese Journal of Mechanical Engineering 2023 36:7 -
Terahertz Spectroscopic Characterization and Thickness Evaluation of Internal Delamination Defects in GFRP Composites
The use of terahertz time-domain spectroscopy (THz-TDS) for the nondestructive testing and evaluation (NDT&E) of materials and structural systems has attracted significant attention over the past two decades d...
Citation: Chinese Journal of Mechanical Engineering 2023 36:6 -
Surface Integrity of Inconel 738LC Parts Manufactured by Selective Laser Melting Followed by High-speed Milling
This study is concerned with the surface integrity of Inconel 738LC parts manufactured by selective laser melting (SLM) followed by high-speed milling (HSM). In the investigation process of surface integrity, ...
Citation: Chinese Journal of Mechanical Engineering 2023 36:5 -
Experimental Research on the Surface Quality of Milling Contour Bevel Gears
Contour bevel gears have the advantages of high coincidence, low noise and large bearing capacity, which are widely used in automobile manufacturing, shipbuilding and construction machinery. However, when the ...
Citation: Chinese Journal of Mechanical Engineering 2023 36:4 -
Simulation Analysis of Torsion Beam Hydroforming Based on the Fluid-Solid Coupling Method
Hydroformed parts are widely used in industrial automotive parts because of their higher stiffness and fatigue strength and reduced weight relative to their corresponding cast and welded parts. This paper repo...
Citation: Chinese Journal of Mechanical Engineering 2023 36:3 -
Evaluation of Surface Roughness of Aluminum Alloy in Burnishing Process Based on Chaos Theory
Burnishing experiments with different burnishing parameters were performed on a computer numerical control milling machine to characterize the surface roughness of an aluminum alloy during burnishing. The chao...
Citation: Chinese Journal of Mechanical Engineering 2023 36:2 -
Multiscale Theories and Applications: From Microstructure Design to Macroscopic Assessment for Carbon Nanotubes Networks
Carbon nanotube (CNT) networks enable CNTs to be used as building blocks for synthesizing novel advanced materials, thus taking full advantage of the superior properties of individual CNTs. Multiscale analyses...
Citation: Chinese Journal of Mechanical Engineering 2023 36:1 -
Synchronization and Stability of a Nonlinear Vibrating Mechanical System Characterized by Asymmetrical Piecewise Linearity
In previous studies about the synchronization of vibrators, the restoring forces of springs are mainly treated as linear directly, whereas the nonlinear features are rarely considered in vibrating systems. To ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:151 -
A Novel Braking Control Strategy for Hybrid Electric Buses Based on Vehicle Mass and Road Slope Estimation
Proper braking force distribution strategies can improve both stability and economy performance of hybrid electric vehicles, which is prominently proved by many studies. To achieve better dynamic stable perfor...
Citation: Chinese Journal of Mechanical Engineering 2022 35:150 -
Active Compliance Control of a Position-Controlled Industrial Robot for Simulating Space Operations
An industrial robot with a six-axis force/torque sensor is usually used to produce a zero-gravity environment for testing space robotic operations. However, using traditional force control methods, such as adm...
Citation: Chinese Journal of Mechanical Engineering 2022 35:149 -
Recent Advances in Drilling Tool Temperature: A State-of-the-Art Review
Drilling is regarded as the most complex manufacturing process compared with other conventional machining processes. During the drilling process, most of the energy consumed in metal cutting is converted to he...
Citation: Chinese Journal of Mechanical Engineering 2022 35:148 -
Novel Hybrid Physics-Informed Deep Neural Network for Dynamic Load Prediction of Electric Cable Shovel
Electric cable shovel (ECS) is a complex production equipment, which is widely utilized in open-pit mines. Rational valuations of load is the foundation for the development of intelligent or unmanned ECS, sinc...
Citation: Chinese Journal of Mechanical Engineering 2022 35:147 -
Principle and Control of Active Engine Mount Based on Magnetostrictive Actuator
Engine mount system affects the automobile NVH performance. Active mounts would achieve excellent vibration isolation and relative displacement control performance in a broad frequency bandwidth by outputting ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:146 -
Relative Varying Dynamics Based Whole Cutting Process Optimization for Thin-walled Parts
Thin-walled parts are typically difficult-to-cut components due to the complex dynamics in cutting process. The dynamics is variant for part during machining, but invariant for machine tool. The variation of t...
Citation: Chinese Journal of Mechanical Engineering 2022 35:145 -
MPC-Based Coordinated Control of Gear Shifting Process for a Power-split Hybrid Electric Bus with a Clutchless AMT
Two-speed clutchless automated manual transmission (AMT) has been widely implemented in electric vehicles for its simple structure and low cost. In contrast, due to the complex response characteristics of powe...
Citation: Chinese Journal of Mechanical Engineering 2022 35:144 -
Neighborhood Modularization-based Artificial Bee Colony Algorithm for Disassembly Planning with Operation Attributes
The recycling and remanufacturing of end-of-life products are significant for environmental protection and resource conservation. Disassembly is an essential process of remanufacturing end-of-life products. Ef...
Citation: Chinese Journal of Mechanical Engineering 2022 35:143 -
Research Progress of Refractory High Entropy Alloys: A Review
Owing to superior comprehensive performance than conventional superalloys at high temperature, refractory high entropy alloy (RHEA) is becoming a promising candidate for the next generation high-temperature ma...
Citation: Chinese Journal of Mechanical Engineering 2022 35:142 -
Design of Passive Constant-Force End-Effector for Robotic Polishing of Optical Reflective Mirrors
Polishing plays an indispensable role in optical processing, especially for large-aperture optical reflective mirrors with freeform surfaces. Robotic polishing requires effective control of the contact force b...
Citation: Chinese Journal of Mechanical Engineering 2022 35:141 -
Microstructure and Mechanical Properties of Nickel-Aluminum Bronze Coating on 17-4PH Stainless Steel by Laser Cladding
Bimetallic copper-steel composite could be an effective structural material to improve the performance of traditional nickel-aluminum bronze (NAB) ship propeller due to its high structural strength and corrosi...
Citation: Chinese Journal of Mechanical Engineering 2022 35:140 -
Fabrication of Ordered Micro/Nanostructures Using Probe-Based Force-Controlled Micromachining System
This paper presents a probe-based force-controlled nanoindentation method to fabricate ordered micro/nanostructures. Both the experimental and finite element simulation approaches are employed to investigate t...
Citation: Chinese Journal of Mechanical Engineering 2022 35:139 -
A Novel 6-DOF Force-Sensed Human-Robot Interface for an Intuitive Teleoperation
The teleoperation of a 6 degrees-of-freedom (DOF) manipulator is one of the basic methods to extend people’s capabilities in the wide variety of applications. The master interface based on the force/torque (FT...
Citation: Chinese Journal of Mechanical Engineering 2022 35:138 -
Corrosion Resistance and Tribological Properties of Laser Cladding Layer of H13 Die Steel Strengthened by Ultrasonic Rolling
Laser cladding is a new surface repair method that can improve the wear and corrosion resistance of substrate surfaces. However, the cladding layer typically exhibits a rough surface, high hardness and large r...
Citation: Chinese Journal of Mechanical Engineering 2022 35:137 -
Development and Control of a Magnetorheological Damper-Based Brake Pedal Simulator for Vehicle Brake-by-Wire Systems
Recent developments have demonstrated that the brake pedal simulator (BPS) is becoming an indispensable apparatus for the break-by-wire systems in future electric vehicles. Its main function is to provide the ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:136 -
Mobile Robot Combination Autonomous Behavior Strategy to Inspect Hazardous Gases in Relatively Narrow Man–Machine Environment
Selecting the optimal speed for dynamic obstacle avoidance in complex man–machine environments is a challenging problem for mobile robots inspecting hazardous gases. Consideration of personal space is importan...
Citation: Chinese Journal of Mechanical Engineering 2022 35:135 -
Vehicular Electronic Image Stabilization System Based on a Gasoline Model Car Platform
Noise, vibration and harshness (NVH) problems in vehicle engineering are always challenging in both traditional vehicles and intelligent vehicles. Although high accuracy manufacturing, modern structural roads ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:134 -
Feasibility Study of the GST-SVD in Extracting the Fault Feature of Rolling Bearing under Variable Conditions
Feature information extraction is one of the key steps in prognostics and health management of rotating machinery. In the present study, an investigation about the feasibility of a methodology based on general...
Citation: Chinese Journal of Mechanical Engineering 2022 35:133 -
A Discrete Multi-Objective Artificial Bee Colony Algorithm for a Real-World Electronic Device Testing Machine Allocation Problem
With the continuous development of science and technology, electronic devices have begun to enter all aspects of human life, becoming increasingly closely related to human life. Users have higher quality requi...
Citation: Chinese Journal of Mechanical Engineering 2022 35:132 -
Three-Dimensional Numerical Study on the Metal Rotating Spray Transfer Process of High-Current GMAW
A three-dimensional numerical model based on the volume-of-fluid (VOF) method is typically preferred for studying high-current gas metal arc welding (GMAW) metal transfer mechanism and then controlling it. It ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:131 -
Optimal Design and Experimental Verification of Low Radiation Noise of Gearbox
Reducing the radiated noise of a gearbox is a difficult problem in aviation, navigation, machinery, and other fields. Structural improvement is the main means of noise reduction for a gearbox, and it is realiz...
Citation: Chinese Journal of Mechanical Engineering 2022 35:130 -
Laser Oscillating of Nickel Alloyed Welds on Press-Hardened Steel
Laser oscillating welding was employed to fabricate Al-Si coated press-hardened steel (PHS) to improve the element homogeneity in the fusion zone. Laser oscillating welding was employed with various oscillatio...
Citation: Chinese Journal of Mechanical Engineering 2022 35:129 -
Research on the Pressure Regulator Effect on a Pneumatic Vibration Isolation System
The pneumatic vibration isolator (PVI) plays an increasingly important role in precision manufacturing. In this paper, aiming to detect the performance of the pressure regulator in the PVI system, a PVI testin...
Citation: Chinese Journal of Mechanical Engineering 2022 35:128 -
Velocity Constraints Based Approach for Online Trajectory Planning of High-Speed Parallel Robots
High-speed parallel robots have been extensively utilized in the light industry. However, the influence of the nonlinear dynamic characteristics of high-speed parallel robots on system’s dynamic response and s...
Citation: Chinese Journal of Mechanical Engineering 2022 35:127 -
Prediction and Minimization of the Heat Treatment Induced Distortion in 8620H Steel Gear: Simulation and Experimental Verification
The considerable heat treatment induced runout value in the end face of the automobile main reducer gear is always dimensionally out of tolerance. It directly affects the dimensional accuracy, the grade of car...
Citation: Chinese Journal of Mechanical Engineering 2022 35:126 -
Numerical Simulation and Experimental Verification of Laser Multi-Section Welding
To address the problems of large welding deformation and splashing in the resistance spot welding of the lubricating oil cooler plate, the laser spot welding was employed, instead of the resistance spot weldin...
Citation: Chinese Journal of Mechanical Engineering 2022 35:125 -
Design and Analysis of a Novel Compliant Mechanism with RPR Degrees of Freedom
A novel compliant mechanism with RPR degrees of freedom (DOF) is proposed where R and P represent rotation and translation DOFs, respectively. The proposed compliant mechanism is obtained from dimension synthe...
Citation: Chinese Journal of Mechanical Engineering 2022 35:124 -
Kinematic, Workspace and Force Analysis of A Five-DOF Hybrid Manipulator R(2RPR)R/SP+RR
In the present study, the over-constrained hybrid manipulator R(2RPR)R/SP+RR is considered as the research objective. In this paper, kinematics of the hybrid manipulator, including the forward and inverse posi...
Citation: Chinese Journal of Mechanical Engineering 2022 35:123 -
Analytical Modelling and Experiment of Novel Rotary Electro-Mechanical Converter with Negative Feedback Mechanism for 2D Valve
The manufacturing of spiral groove structure of two-dimensional valve (2D valve) feedback mechanism has shortcomings of both high cost and time-consuming. This paper presents a novel configuration of rotary el...
Citation: Chinese Journal of Mechanical Engineering 2022 35:122 -
Theoretical Model of Dynamic Bulk Modulus for Aerated Hydraulic Fluid
Existing models of bulk modulus for aerated hydraulic fluids primarily focus on the effects of pressure and air fraction, whereas the effect of temperature on bulk modulus is disregarded. Based on the lumped p...
Citation: Chinese Journal of Mechanical Engineering 2022 35:121 -
Driving Environment Uncertainty-Aware Motion Planning for Autonomous Vehicles
Autonomous vehicles require safe motion planning in uncertain environments, which are largely caused by surrounding vehicles. In this paper, a driving environment uncertainty-aware motion planning framework is...
Citation: Chinese Journal of Mechanical Engineering 2022 35:120 -
Inverse Dynamics of A 3-DOF Parallel Mechanism Based on Analytical Forward Kinematics
For the development of a parallel mechanism (PM), it is necessary to establish a dynamic model which can accurately meet the requirements of real-time control. Compared with the general dynamic analysis model ...
Citation: Chinese Journal of Mechanical Engineering 2022 35:119 -
Investigation of Movement and Deposition Behaviors of Solid Particles in Hydraulic Water Reservoir via the CFD-DEM Coupling Method
Solid contamination existing as solid particles in power fluid transmission systems may lead to transmission performance reduction, system failures, and component damage. The hydraulic reservoir will deposit t...
Citation: Chinese Journal of Mechanical Engineering 2022 35:118 -
Plastic–elastic Model for Water-based Lubrication Considering Surface Force
Water-based lubrication is an effective method to achieve superlubricity, which implies a friction coefficient in the order of 10−3 or lower. Recent numerical, analytical, and experimental studies confirm that th...
Citation: Chinese Journal of Mechanical Engineering 2022 35:117 -
Flexible Scanning Method by Integrating Laser Line Sensors with Articulated Arm Coordinate Measuring Machines
Measuring and reconstructing the shape of workpieces have been considered as a fundamental step in both reverse engineering and product quality control. Owing to increasing structural complexity of recent prod...
Citation: Chinese Journal of Mechanical Engineering 2022 35:116
Associated Society
Annual Journal Metrics
-
2022 Citation Impact
4.2 - 2-year Impact Factor
3.9 - 5-year Impact Factor
1.546 - SNIP (Source Normalized Impact per Paper)
0.744 - SJR (SCImago Journal Rank)2023 Speed
43 days submission to first editorial decision for all manuscripts (Median)
431 days submission to accept (Median)2023 Usage
814,514 downloads
17 Altmetric mentions -
This journal is indexed by
• Google Scholar
• EBSCO
• EI Compendex
• SCImago
• SCIE
• UGC-CARE List (India)
• Dimensions
• DOAJ
• Astrophysics Data System (ADS)
• ProQuest
• Chinese Academy of Sciences (CAS) - GoOA
• Naver
• CNKI
• Chinese Science Citation Database
• OCLC WorldCat Discovery Service
• Chemical Abstracts Service (CAS)
• TD Net Discovery Service
• SCOPUS
• INSPEC
• CNPIEC
- ISSN: 2192-8258 (electronic)
- ISSN: 1000-9345 (print)